Robbed-bit signaling

In communication systems the robbed-bit signaling, also known as Channel –Associated Signaling (CAS) is a scheme utilized to provide maintenance services on T1 digital carrier circuits. The T1 carrier circuit is a type of dedicated circuit currently employed in North America and Japan. The T1 circuit is divided into 24 channels, each carrying 8,000 samples per second, each 8 bits long. The Super Frame (SF) consist of 12 frames of 24 channels. The DS1 designation consist of 24 frames called, Extended Super Frame (ESF). In either designation, these channels are multiplexed together and sample at 8000 bit/s. In the DS0 designation, each of the channels induces eight bits into the multiplex output stream, ten are utilized entirely for voice/data and two are utilized partially for voice. Hence, each of the two partial channels yields 7 x 8000 bit/s = 56 kbit/s for voice data and the remaining channels yields 8 x 8000 bit/s = 64 kbit/s.[1]

T1 Carrier DesignationDS DesignationSpeed
FT1DS064 kbit/s
T1DS11.544 Mbit/s
T2DS26.312 Mbit/s
T3DS344.376 Mbit/s
T4DS4274.176 Mbit/s

[2] Intuitively we can analyze that 5 out of 6 frames have 8 bit resolution equal to 64 Kbps (8 Bits x 8,000 Samples per Second = 64 Kbps) and 1 out of every 6 frames has a 7 bit resolution (7 Bits x 8,000 Samples per Second = 56 Kbps) The distortion effect on voice and data signals is negligible when a modem is used for modulation. However, for a 64 kbit/s digital signals the data will render errors when data signal is transmitted. If such is the case the robbed-bit signaling should be turned off.

The robbed-bit signal scheme is used in the super frame circuit (SF). It takes the least significant bit of every sixth channel and utilizes it to convey on or off hook, and busy signal status on telephone lines. The first bit of every six is called A bit, the second bit is called B bit.[3]

RBS was developed at the time that AT&T was moving from analog trunks onto digital equipment. This permitted AT&T to run 24 digital phone lines on the same number of wires that 2 analog phone lines would have taken, saving money and improving call quality, without the high cost of frequency-division multiplexing.

As in other carrier systems, the physical properties of an actual trunk wire are missing. With analog trunks, to signal the equipment at the far end that a trunk was going to be used, equipment would "loop" the line by connecting the wires together at one end or ground start one of the wires (depending on the type of trunk), and do the opposite to return the trunk to idle. With a digital trunk, another method was needed to signal between ends.

To do this, signaling equipment "steals" the eighth bit of each channel on every sixth frame (see Super Frame and Extended Super Frame) and replaces it with signalling information. Put another way, this means that the low-order bit on every sixth sample in every DS0 carried on the T1, in either direction, is replaced by signalling information. Simple PCM-encoded voice is not very sensitive to losing this data in a few of its lower-order bits, so it doesn't cause much degradation of voice quality; however, when carrying data, the difference is significant, reducing the available usable data rate by 12.5%. With full 64 kbit/s, a voice channel has a signal-to-noise ratio of 37 decibels (dB). At 56 kbit/s, a voice channel has a signal to noise ratio of 31 dB. As only every sixth least-significant bit is robbed, the signal to noise ratio will be somewhere between 31 and 37 dB. However, since individual T1 links are not in general synchronized to one another, a DS0 passing along several concatenated, unsynchronized, T1 spans may have its lower bit stolen in more than one frame, frequently making real-world performance closer to the lower-bound than the upper bound of signal-to-noise performance.

Robbed-bit signaling can have an effect on audio quality under certain circumstances, though. When a voice call is connected to a quiet termination, as can happen when on hold in a PBX which does not have music on hold or comfort noise enabled, and certain types of framing circuits are used, the noise due to robbed-bit signaling can be heard in the handset as a faint 1333 Hz tone, this frequency being a result of low-bit corruption at a rate of 8000 Hz / 6 = 1333 Hz. This is normally not a very noticeable problem, but if the audio path contains in-line speech compression, such asG.729, the tone can be amplified and modulated by the compression algorithm to the point of annoyance to the user.

With Super Frame framing, the robbed bits are named A and B. With Extended Super Frame, the same stream is divided into four bits, named A, B, C, and D. The meanings of these bits depend on what type of signalling is provisioned on the channel. The most common types of signaling are loop start, ground start, and E&M.

Unlike T1 systems, most telephone systems in the world use E1 systems that transparently pass all 8 bits of every sample. Those systems use a separate out-of-band channel to carry the signalling information.


  1. ^ green, harry. the irwing handbook of telecommunications. new york: mcgraw-hill, 2000.
  2. ^ Dennis, Jerry Fitzgerald & Alan. Business Data Communications and Networking. Hoboken: John Wiley & Sons Inc, n.d.
  3. ^ Tanenbaum, Andrew S.. Computer Networks. Upper Saddle River: Prentice Hall PTR, 2003